PointedThree - Tricky part no

Welcome Guest. ( logon | register )

FAQ

Member List

Albums

Today's Posts

PointedThree : Vans, Trucks, SUVs and Other Forums : G-Class : Tricky part no

Page 1 of 1

Tricky part no

Topic Tools

Message Format

Author

Posted 4/10/2007 2:41 PM

petermerle
Expert

Date registered: Apr 2006
Location: Cape Town ( deep south )
Vehicle(s): W460 *1, W123 *2, W124
Posts: 1315
1000

Tricky part no

I'm looking for the bracket that holds the Power Steering hoses to the cylinder head on an early 300GD - Vin 46033227021345. I cannot seem to find this item on the EPC!
Peter

#69640

Author

Posted 4/10/2007 4:07 PM

JMKOZ
Veteran

Date registered: Apr 2006
Location: Melbourne Australia
Vehicle(s): 2018 G300 cdi Professional Wagon
Posts: 155
100

RE: Tricky part no

Hi Peter,

I'm not sure if this is the part you are looking for but if it is Part No.s 59 & 75 in the attached photo then it will be A4604660140 and A6179950432 respectively.

Regards John

Edited by JMKOZ 4/10/2007 4:08 PM

(EPC Steering 1.gif)

Attachments
----------------

EPC Steering 1.gif (19KB - 1 downloads)
Attachments

EPC Steering 1.gif (19KB - 0 downloads)

#69650 - in reply to #69640

Author

Posted 4/10/2007 8:15 PM

hipine

Date registered: Jul 2006
Location: US, CO, Bailey
Vehicle(s): 460 1980 280GE w. 617A
5000

RE: Tricky part no

The RHD 300GD I have has long rubber hoses going across the front of the cylinder head near top of engine, not the metal pipes crossing low like that EPC pic seems to indication.

I don't know the part number, Peter, but I could send you pix of the one I have! :^) I haven't tried looking up the VIN for this truck....maybe I should. Now if I can only remember what I did with the ID tag when I scrapped the body.... 'course I can always check the chassis rail.

-Dave G.

#69679 - in reply to #69650

Author

Posted 4/11/2007 4:44 PM

petermerle
Expert

Date registered: Apr 2006
Location: Cape Town ( deep south )
Vehicle(s): W460 *1, W123 *2, W124
Posts: 1315
1000

RE: Tricky part no

Those parts are unfortunately only valid for later vins's ( after 31425 ) , mine is an earlier one - 21345 - there is no mention of the earlier one. I have seen the bracket - its a simple straight vertical one mounted to cyl head at the front lift point - but cannot find it on EPC!
Peter

#69773 - in reply to #69650

Author

Posted 4/11/2007 6:22 PM

EuroTruck
Extreme Veteran

Date registered: Apr 2006
Location: Oakwood, Georgia - USA
Vehicle(s): 2012 Audi A4 Avant S-Line, 2015 Ridley NOAH SL
Posts: 518
500

RE: Tricky part no

Peter,

Any of these brackets resemble your part? If so, you'll find them in the engine section under "13 - Power Steering Pump".

If none of these are correct, the EPC shows that #41 in the diagram John posted as being the bracket now used on the earlier trucks.

-Sean

(Steering Bracket.jpg)

Attachments
----------------

Steering Bracket.jpg (61KB - 5 downloads)

#69793 - in reply to #69640

Author

Posted 4/12/2007 2:02 AM

petermerle
Expert

Date registered: Apr 2006
Location: Cape Town ( deep south )
Vehicle(s): W460 *1, W123 *2, W124
Posts: 1315
1000

RE: Tricky part no

None of those are correct. #41 which is the P clip holding pipe to bracket is correct , but no bracket is shown for older RHD model. Got a picture from above attached