Welcome Guest. ( logon | register ) | ||||||
|
|
|
| Topic Tools | Message Format |
Author |
| ||
petermerle Expert Date registered: Apr 2006 Location: Cape Town ( deep south ) Vehicle(s): W460 *1, W123 *2, W124 Posts: 1315 | Tricky part no I'm looking for the bracket that holds the Power Steering hoses to the cylinder head on an early 300GD - Vin 46033227021345. I cannot seem to find this item on the EPC! Peter | ||
#69640 | |||
Author |
| ||
JMKOZ Veteran Date registered: Apr 2006 Location: Melbourne Australia Vehicle(s): 2018 G300 cdi Professional Wagon Posts: 155 | RE: Tricky part no Hi Peter, I'm not sure if this is the part you are looking for but if it is Part No.s 59 & 75 in the attached photo then it will be A4604660140 and A6179950432 respectively. Regards John
Edited by JMKOZ 4/10/2007 4:08 PM (EPC Steering 1.gif) (EPC Steering 1.gif) Attachments ---------------- EPC Steering 1.gif (19KB - 1 downloads) EPC Steering 1.gif (19KB - 0 downloads) | ||
#69650 - in reply to #69640 | |||
Author |
| ||
hipine Date registered: Jul 2006 Location: US, CO, Bailey Vehicle(s): 460 1980 280GE w. 617A | RE: Tricky part no The RHD 300GD I have has long rubber hoses going across the front of the cylinder head near top of engine, not the metal pipes crossing low like that EPC pic seems to indication. I don't know the part number, Peter, but I could send you pix of the one I have! :^) I haven't tried looking up the VIN for this truck....maybe I should. Now if I can only remember what I did with the ID tag when I scrapped the body.... 'course I can always check the chassis rail. -Dave G. | ||
#69679 - in reply to #69650 | |||
Author |
| ||
petermerle Expert Date registered: Apr 2006 Location: Cape Town ( deep south ) Vehicle(s): W460 *1, W123 *2, W124 Posts: 1315 | RE: Tricky part no Those parts are unfortunately only valid for later vins's ( after 31425 ) , mine is an earlier one - 21345 - there is no mention of the earlier one. I have seen the bracket - its a simple straight vertical one mounted to cyl head at the front lift point - but cannot find it on EPC! Peter | ||
#69773 - in reply to #69650 | |||
Author |
| ||
EuroTruck Extreme Veteran Date registered: Apr 2006 Location: Oakwood, Georgia - USA Vehicle(s): 2012 Audi A4 Avant S-Line, 2015 Ridley NOAH SL Posts: 518 | RE: Tricky part no Peter,
Any of these brackets resemble your part? If so, you'll find them in the engine section under "13 - Power Steering Pump". If none of these are correct, the EPC shows that #41 in the diagram John posted as being the bracket now used on the earlier trucks.
-Sean (Steering Bracket.jpg) Attachments ---------------- Steering Bracket.jpg (61KB - 5 downloads) | ||
#69793 - in reply to #69640 | |||
Author |
| ||
petermerle Expert Date registered: Apr 2006 Location: Cape Town ( deep south ) Vehicle(s): W460 *1, W123 *2, W124 Posts: 1315 | RE: Tricky part no None of those are correct. #41 which is the P clip holding pipe to bracket is correct , but no bracket is shown for older RHD model. Got a picture from above attached (BRACKET.JPG) Attachments ---------------- BRACKET.JPG (81KB - 0 downloads) | ||
#69814 - in reply to #69793 | |||
Author |
| ||
Inkblotz Expert Date registered: Apr 2006 Location: Georgia Vehicle(s): 90 300GD "Thundering Turtle II", w/ 603A turbo Posts: 3186 | RE: Tricky part no Do any of these do the trick? (Picture 2.png) (Picture 3.png) Attachments ---------------- Picture 2.png (76KB - 1 downloads) Picture 3.png (78KB - 0 downloads) | ||
#70281 - in reply to #69640 | |||
Author |
| ||
petermerle Expert Date registered: Apr 2006 Location: Cape Town ( deep south ) Vehicle(s): W460 *1, W123 *2, W124 Posts: 1315 | Re: Tricky part no None, I've also gone through EPC and cant find it! Peter | ||
#70314 - in reply to #69640 | |||
« View previous thread :: View next thread » |
|
|